COMPLETE SOLUTIONS
Composition:
- Terrasit EPS F Super, (0.038 W / mK) EPS facade panel
- Insulating covering PLUG (EPS F) and the retaining anchor
- Terracokl (0.037 W / mK, min. 15 cm), waterproof EPS panel
- Insulating covering PLUG (EPS F) and tether anchor
Composition:
- Terrasit EPS F Grafit, (0.032 W / mK) EPS facade panel
- Insulating covering PLUG (GRAFIT) and the retaining anchor
- Terracokl GRAFIT (0.031 W / mK, min. 13 cm), waterproof EPS panel
- Insulating covering PLUG (GRAFIT) and tether anchor
Composition:
- Existing insulation
- Terrasit EPS F Grafit, (0.032 W / mK), or EPS F Super (0.037 W / mK), panel flap
- Insulating covering PLUG and tether anchor
- Terracokl (0.037 W / mK, min. 13 cm), waterproof EPS panel
- Insulating covering PLUG and tether anchor
Installation = 0.16 W / m2K LOW ENERGY HOUSE
Composition:
- Terrasit EPS F (0.037 W / mK, min.20 cm), facade EPS panel
- Terracokl (0.037 W / mK, min. 18 cm), waterproof EPS panel
- Insulating COVERING PLUG (EPS F) and the S retaining anchor
- Installation = 0.16 W / m2K, with a brick wall thickness of 29 cm (λ≤0,25 W / mK)
Thermal insulation of facades
Installation = 0.13 W / m2K LOW ENERGY HOUSE
Composition:
- Terrasit EPS F GRAFIT (0.032 W / mK, min.20 cm), facade EPS panel
- Terracokl GRAFIT (0.031 W / mK, min. 18 cm), waterproof EPS panel
- Insulating covering plug and tether anchor
- installation = 0.13 W / m2K, with a brick wall thickness of 29 cm (λ≤0,25 W / mK)
Thermal insulation of facades
“COMPLETED zero-energy house”
installation = 0.09 W / m2K
Composition:
- Terrasit EPS F GRAFIT (0.031 W / mK, min.30 cm), facade EPS panel
- Terracokl graphite (0.031 W / mK, min. 28 cm), waterproof EPS panel
- Insulating covering PLUG and tether anchor
- installation = 0.09 W / m2K, with a brick wall thickness of 29 cm (λ≤0,25 W / mK)
Thermal insulation of facades
“COMPLETED zero-energy house”
installation = 0.09 W / m2K
Composition:
- Terrasit EPS F GRAFIT (0.031 W / mK, min.30 cm), facade EPS panel
- Terracokl graphite (0.031 W / mK, min. 28 cm), waterproof EPS panel
- Insulating covering PLUG and tether anchor
- installation = 0.09 W / m2K, with a brick wall thickness of 29 cm (λ≤0,25 W / mK)
Floor with the damping of impact sounds of up to 26 dB
Load up to 1000 kg / m2
- Screed ≥ 75 kg / m2
- Terraestrih EPS T 22/20
- AB board
- Insulation below unheated space such. TERRASIT EPS F GRAFIT
- STIROTRAK-edge trimmings
Floor with the insulation of lightweight concrete with EPS granules
- Screed ≥ 75 kg / m2
- TERRAESTRIH EPS T
- EPS granules, ρ = 200 kg / m3, watered installation layer with lightweight insulating concrete (λ = 0.045 W / mK)
- Insulation below unheated space such as TERRASIT EPS F GRAFIT
- STIROTRAK-edge trimmings
Reconstruction of the wooden ceiling with a light floor with EPS granules
- Laminate or laminated floor, loosely laid
- EPS granules, ρ = 300 kg / m3, lightweight concrete reinforced with steel mesh,
- thickness ≥ 8 cm (approximately 25kg / m2), as required, leveling the surface with mortar and built-alkaline-resistant fiberglass mesh.
- Water vapor permeable, separation layer of felt 300 g / m2
- STIROTRAK-edge trimmings
* In consultation with experts
Under the ground
Residential and commercial buildings
- Screed
- TERRASIT EPS 100 or EPS TERRASIT 150(for insulation thickness above 20 cm-low energy buildings)
- TERRASIT EPS 100, lightweight concrete with EPS granules (λ = 0.065 W / mK), a layer between installations
- Waterproofing IZOTEKT T4 plus
- STIROTRAK-edge trimmings
- TERRASIT EPS granules poured in the front row of the wall, to reduce the influence of thermal bridge
Floor with increased loads
Garages, boiler rooms, industrial flooring
- Floor (above 7 cm)
- TERRASIT EPS 150 (even loads up to 3000 kg)
- Waterproofing IZOTEKT T4 plus
- STIROTRAK-edge trimmings
Lightweight insulation floor EPS GRANULE
Adaptation of floors with limited heights
- Top layer (ceramic, laminate)
- EPS granules, ρ = 300 kg7m3, reinforced lightweight concrete, thickness ≥ 6 cm, min.3 cm above installation
- Waterproofing IZOTEKT T4 plus
- STIROTRAK-edge trimmings
Rehabilitation of concrete floor-enhanced insulation power
- Screed
- TERRASIT EPS 200 (0.034 W / mK)
- Waterproofing IZOTEKT T4 plus
- STIROTRAK-edge trimmings
Flat roof with insulation plates at an incline
Composition:
- Concrete slabs laid in sand, separation layer
- XPS 300 GL (in the case of DUO roof)
- Waterproofing: IZOELAST P5 plus and IZOSELF P3, masking tape
- INSULATION in the slopes of 0.5%, 1%, 1.5%, 2% (EPS 100 or 150 kPa)
- TERRASIT EPS 100
- BITALBIT AL V4
- AB board, IBITOL-primer
Flat roof with insulation plates at an incline
increased capacity
Composition:
- Concrete slabs laid in sand, separation layer
- FRAGMAT XPS 300 GL (in the case of DUO roof)
- Waterproofing IZOELAST P5 plus and IZOSELF P3, masking tape
- INSULATION in the slopes of 0.5%, 1%, 1.5%, 2%
- TERRASIT EPS 200
- BITALBIT AL V4, vapor barrier
- AB board, IBITOL-primer
Flat roof with insulation plates at an incline
increased capacity
Composition:
- Concrete slabs laid in sand, separation layer
- FRAGMAT XPS 300 GL (in the case of DUO roof)
- Waterproofing IZOELAST P5 plus and IZOSELF P3, masking tape
- INSULATION in the slopes of 0.5%, 1%, 1.5%, 2%
- TERRASIT EPS 200
- BITALBIT AL V4, vapor barrier
- AB board, IBITOL-primer
Thermal insulation of cold attic – occasionally walkable surface
Composition:
- TERRASIT EPS 150 (0.034 W / mK), walkable layer
- TERRASIT ESA 70 (0.039 W / mK)
- Thermal bridge insulation, EPS 70
Thermal insulation of cold attic – walkable surface
Composition:
- EPS GRANULE ρ ≥ 200 kg / m3, lightweight insulation under (λ = 0.065 W / mK)
- TERRASIT EPS 70 (0.039 W / mK)
- Vapor barrier, PE film
- Thermal bridge insulation, EPS 70
Thermal insulation of cold attic – impassable surface
Composition:
- TERRASIT EPS 70 (0.039 W / mK)
- Vapor barrier (in the case of additional coats)
- Thermal bridge insulation, EPS 70