Thermal insulation of facades

Composition:

  1. Terrasit EPS F Super, (0.038 W / mK) EPS facade panel
  2. Insulating covering PLUG (EPS F) and the retaining anchor
  3. Terracokl (0.037 W / mK, min. 15 cm), waterproof EPS panel
  4. Insulating covering PLUG (EPS F) and tether anchor

Thermal insulation of facades-enhanced insulation power

Composition:

  1. Terrasit EPS F Grafit, (0.032 W / mK) EPS facade panel
  2. Insulating covering PLUG (GRAFIT) and the retaining anchor
  3. Terracokl GRAFIT (0.031 W / mK, min. 13 cm), waterproof EPS panel
  4. Insulating covering PLUG (GRAFIT) and tether anchor

Thermal insulation of the façade – with an existing insulation

Composition:

  1. Existing insulation
  2. Terrasit EPS F Grafit, (0.032 W / mK), or EPS F Super (0.037 W / mK), panel flap
  3. Insulating covering PLUG and tether anchor
  4. Terracokl (0.037 W / mK, min. 13 cm), waterproof EPS panel
  5. Insulating covering PLUG and tether anchor

Thermal insulation of facades

Installation = 0.16 W / m2K LOW ENERGY HOUSE

Composition:

  1. Terrasit EPS F (0.037 W / mK, min.20 cm), facade EPS panel
  2. Terracokl (0.037 W / mK, min. 18 cm), waterproof EPS panel
  3. Insulating COVERING PLUG (EPS F) and the S retaining anchor
  4. Installation = 0.16 W / m2K, with a brick wall thickness of 29 cm (λ≤0,25 W / mK)

Thermal insulation of facades

Installation = 0.13 W / m2K LOW ENERGY HOUSE

Composition:

  1. Terrasit EPS F GRAFIT (0.032 W / mK, min.20 cm), facade EPS panel
  2. Terracokl GRAFIT (0.031 W / mK, min. 18 cm), waterproof EPS panel
  3. Insulating covering plug and tether anchor
  4. installation = 0.13 W / m2K, with a brick wall thickness of 29 cm (λ≤0,25 W / mK)

Thermal insulation of facades

“COMPLETED zero-energy house”

installation = 0.09 W / m2K

Composition:

  1. Terrasit EPS F GRAFIT (0.031 W / mK, min.30 cm), facade EPS panel
  2. Terracokl graphite (0.031 W / mK, min. 28 cm), waterproof EPS panel
  3. Insulating covering PLUG and tether anchor
  4. installation = 0.09 W / m2K, with a brick wall thickness of 29 cm (λ≤0,25 W / mK)

Thermal insulation of facades

“COMPLETED zero-energy house”

installation = 0.09 W / m2K

Composition:

  1. Terrasit EPS F GRAFIT (0.031 W / mK, min.30 cm), facade EPS panel
  2. Terracokl graphite (0.031 W / mK, min. 28 cm), waterproof EPS panel
  3. Insulating covering PLUG and tether anchor
  4. installation = 0.09 W / m2K, with a brick wall thickness of 29 cm (λ≤0,25 W / mK)

Floor with the damping of impact sounds of up to 26 dB

Load up to 1000 kg / m2

  1. Screed ≥ 75 kg / m2
  2. Terraestrih EPS T 22/20
  3. AB board
  4. Insulation below unheated space such. TERRASIT EPS F GRAFIT
  5. STIROTRAK-edge trimmings

Floor with the insulation of lightweight concrete with EPS granules

  1. Screed ≥ 75 kg / m2
  2. TERRAESTRIH EPS T
  3. EPS granules, ρ = 200 kg / m3, watered installation layer with lightweight insulating concrete (λ = 0.045 W / mK)
  4. Insulation below unheated space such as TERRASIT EPS F GRAFIT
  5. STIROTRAK-edge trimmings

Reconstruction of the wooden ceiling with a light floor with EPS granules

  1. Laminate or laminated floor, loosely laid
  2. EPS granules, ρ = 300 kg / m3, lightweight concrete reinforced with steel mesh,
  3. thickness ≥ 8 cm (approximately 25kg / m2), as required, leveling the surface with mortar and built-alkaline-resistant fiberglass mesh.
  4. Water vapor permeable, separation layer of felt 300 g / m2
  5. STIROTRAK-edge trimmings

* In consultation with experts

Under the ground

Residential and commercial buildings

  1. Screed
  2. TERRASIT EPS 100 or EPS TERRASIT 150(for insulation thickness above 20 cm-low energy buildings)
  3. TERRASIT EPS 100, lightweight concrete with EPS granules (λ = 0.065 W / mK), a layer between installations
  4. Waterproofing IZOTEKT T4 plus
  5. STIROTRAK-edge trimmings
  6. TERRASIT EPS granules poured in the front row of the wall, to reduce the influence of thermal bridge

Floor with increased loads

Garages, boiler rooms, industrial flooring

  1. Floor (above 7 cm)
  2. TERRASIT EPS 150 (even loads up to 3000 kg)
  3. Waterproofing IZOTEKT T4 plus
  4. STIROTRAK-edge trimmings

Lightweight insulation floor  EPS GRANULE

Adaptation of floors with limited heights

  1. Top layer (ceramic, laminate)
  2. EPS granules, ρ = 300 kg7m3, reinforced lightweight concrete, thickness ≥ 6 cm, min.3 cm above installation
  3. Waterproofing IZOTEKT T4 plus
  4. STIROTRAK-edge trimmings

Rehabilitation of concrete floor-enhanced insulation power

  1. Screed
  2. TERRASIT EPS 200 (0.034 W / mK)
  3. Waterproofing IZOTEKT T4 plus
  4. STIROTRAK-edge trimmings

Flat roof with insulation plates at an incline

Composition:

  1. Concrete slabs laid in sand, separation layer
  2. XPS 300 GL (in the case of DUO roof)
  3. Waterproofing: IZOELAST P5 plus and IZOSELF P3, masking tape
  4. INSULATION in the slopes of 0.5%, 1%, 1.5%, 2% (EPS 100 or 150 kPa)
  5. TERRASIT EPS 100
  6. BITALBIT AL V4
  7. AB board, IBITOL-primer

Flat roof with insulation plates at an incline

increased capacity

Composition:

  1. Concrete slabs laid in sand, separation layer
  2. FRAGMAT XPS 300 GL (in the case of DUO roof)
  3. Waterproofing IZOELAST P5 plus and IZOSELF P3, masking tape
  4. INSULATION in the slopes of 0.5%, 1%, 1.5%, 2%
  5. TERRASIT EPS 200
  6. BITALBIT AL V4, vapor barrier
  7. AB board, IBITOL-primer

Flat roof with insulation plates at an incline

increased capacity

Composition:

  1. Concrete slabs laid in sand, separation layer
  2. FRAGMAT XPS 300 GL (in the case of DUO roof)
  3. Waterproofing IZOELAST P5 plus and IZOSELF P3, masking tape
  4. INSULATION in the slopes of 0.5%, 1%, 1.5%, 2%
  5. TERRASIT EPS 200
  6. BITALBIT AL V4, vapor barrier
  7. AB board, IBITOL-primer

Thermal insulation of cold attic – occasionally walkable surface

Composition:

  1. TERRASIT EPS 150 (0.034 W / mK), walkable layer
  2. TERRASIT ESA 70 (0.039 W / mK)
  3. Thermal bridge insulation, EPS 70

Thermal insulation of cold attic – walkable surface

Composition:

  1. EPS GRANULE ρ ≥ 200 kg / m3, lightweight insulation under (λ = 0.065 W / mK)
  2. TERRASIT EPS 70 (0.039 W / mK)
  3. Vapor barrier, PE film
  4. Thermal bridge insulation, EPS 70

Thermal insulation of cold attic – impassable surface

Composition:

  1. TERRASIT EPS 70 (0.039 W / mK)
  2. Vapor barrier (in the case of additional coats)
  3. Thermal bridge insulation, EPS 70